C13
Parallel failed.
C13Parallel failed.Défaut
Parallel connection failure between battery units. LED pattern: LED1 ON, LED2 OFF, LED3 ON, LED4 ON.
Single unit may be installed to a parallel system, or wiring connection between parallel units is incorrect/incomplete.
1. Check if a single unit is installed to a parallel system. 2. if this error happens during parallel installation, check wire connections; if connected correctly, finish parallel installation first and then restart the unit. 3. if the problem remains, contact your installer.
Felicitysolar FLA12100 12.5Kwh Battery Energy Storage System User Manual.pdf · page 1C13Parallel failed.Défaut— high
Parallel installation failed; battery cannot establish parallel communication or balance with other packs.
Improper parallel installation or incorrect wire connections between the battery packs in parallel.
1. Please check if single unit is installed to parallel system. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please finish parallel installation first, and then restart the unit. 3. if the problem remains, please contact your installer.
Felicitysolar FLA48200 48V 200Ah 10kWh Lithium Phosphate Battery User Manual.pdf · page 13C13Parallel failed.Critique
Battery pack failed to establish or maintain parallel operation with other packs.
Single unit may be incorrectly set to parallel system; or wiring between parallel-connected battery packs is incorrect/incomplete.
1. Please check if a single unit is installed to the parallel system. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please finish parallel installation first, and then restart the unit. 3. if the problem remains, please contact your installer.
6peluqppy_66a93554057c8.pdf · page 13C13C13Défaut
Parallel failed.
1. Please check if single unit is installed to parallel system. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please finish parallel installation first, and then restart the unit. 3. if the problem remains, please contact your installer.
FLA48250-EU_Manual.pdf · page 8C13Parallel failed.Défaut
Parallel connection / parallel-mode start-up failed.
Parallel condition not satisfied (e.g. pack-to-pack voltage difference ≥3V, or wiring issue between paralleled units).
1. Please check if single unit is installed in parallel system. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please finish parallel installation first, and then Restart the unit. 3. if the problem remains, please contact your installer.
felicitysolar FLA48500 LiFePO4 Battery System for Households User Guide.pdfC13Parallelbetrieb fehlgeschlagen.Défaut
Parallel failed. The battery could not establish a valid parallel configuration with other units.
Parallel-installation error (Fehler im Parallelaufbau): single unit reporting parallel state, mis-wired parallel cabling, or incorrect DIP-switch IDs.
1. Check whether a single unit was incorrectly installed in a parallel system. 2. if the error happens during parallel installation, check wire connections; if connected correctly, finish parallel installation first then restart. 3. if the problem remains, contact your installer. Verify DIP-switch addresses per the DIP code table.
Benutzerhandbuch - Felicity FLS48100SG2.pdfC13Parallel failed.Défaut
Parallel connection / parallel-mode start-up failed.
Parallel condition not satisfied (e.g. pack-to-pack voltage difference ≥3V, or wiring issue between paralleled units).
1. Please check if single unit is installed in parallel system. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please finish parallel installation first, and then Restart the unit. 3. if the problem remains, please contact your installer.
HE-GF-FLA-48500 Manual_20250327_EN.pdfC13Parallel failed.Défaut
Parallel-mode communication / configuration failure displayed on the LCD BMS fault code / flag screen (section 4.4). Applies when the LPBF48100-M is operated in parallel (up to 6 units / 30 kWh per section 2.3).
Single unit installed but the system is configured for parallel operation; or a wiring fault between parallel-connected packs (parallel cable / communication cable / DIP-switch address mis-set per section 4.5). Section 4.5 notes that for parallel operation, battery pack IDs must be set to 1-15 via DIP switches SW1-SW4 and SW5 must be ON for termination on the end pack(s).
1. Please check if single unit is installed to parallel system. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please finish parallel installation first, and then restart the unit. 3. if the problem remains, please contact your installer.
358-010291-07.pdf · page 9C13Parallel failed.Défaut
Battery pack could not satisfy parallel-operation conditions (e.g. voltage difference between local and other packs >3V, or wiring issue).
Single unit configured as parallel slave, mis-wired parallel connection, or voltage mismatch (>3V) between paralleled packs.
1. Please check if single unit is installed to parallel system. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please finish parallel installation first, and then restart the unit. 3. if the problem remains, please contact your installer.
Manual-LPBF48200-H.pdf · page 10C13C13Défaut
1. Please check if single unit is installed to parallel system. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please finish parallel installation first, and t hen Restart the unit. 3. if the problem remains, please contact your installer.
Per the manual: verify whether a single unit is installed in a parallel system; if the error occurs during parallel installation, check wiring connections, complete parallel installation, then restart the unit; if the problem persists, contact your installer.
Felicitysolar LPBF48350 17.5kWh 48V Solar Battery Pack with BMS User Guide.pdfC13Parallel failed.Défaut
Parallel-connection condition not satisfied. Possible causes: (1) a single unit is configured as part of a parallel system; (2) wires are mis-connected during parallel installation.
1. Check if a single unit is wrongly installed to a parallel system. 2. if the error happens during parallel installation, check wires connection. if they are connected correctly, finish parallel installation first, then restart the unit. 3. if the problem remains, please contact your installer.
LUX-E-48100LG03-Lithium-Battery-User-Guide.pdf · page 13C13C13Défaut
1. Please check if single unit is installed to parallel system. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please finish parallel installation first, and then restart the unit. 3. if the problem remains, please contact your installer.
LUX-E-48200LG03-Lithium-Battery-User-Guide.pdf · page 13C13C13Défaut
Single unit may be installed to a parallel system, or wiring during parallel installation may be incorrect.
1. Please check if single unit is installed to parallel system. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please finish parallel installation first, and then restart the unit. 3. if the problem remains, please contact your installer.
LUX-E-48230.250LG03-Lithium-Battery-User-Guide.pdfC13Parallel failed.Avertissement
Parallel-mode handshake/operation between battery packs failed.
1. Check whether a single unit is wrongly installed into a parallel system. 2. if error happens during parallel installation, wires may be misconnected.
1. Please check if single unit is installed to parallel system. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please finish parallel installation first, and then restart the unit. 3. if the problem remains, please contact your installer.
LUX-X-48100LG01-Litium-Battery-User-Guide.pdf · page 17C13Parallel failed.Avertissement
Parallel-mode handshake/operation between battery packs failed.
Either a single unit is wrongly configured for parallel operation, or wires are misconnected during parallel installation.
1. Please check if single unit is installed to parallel system. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please finish parallel installation first, and then restart the unit. 3. if the problem remains, please contact your installer.
358-S010024-03LUX-X-48100LG01-User-manual_compressed.pdf · page 23C13Parallel failed.Défaut
Parallel-connection condition not satisfied. Possible causes: (1) a single unit is configured as part of a parallel system; (2) wires are mis-connected during parallel installation.
1. Please check if single unit is installed in parallel system. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please finish parallel installation first, and then restart the unit. 3. if the problem remains, please contact your installer.
LUX-Y-4828048300LG01-Lithium-Battery-User-Guide.pdf · page 8Compilé à partir des manuels utilisateur officiels FelicityESS. Consultez toujours le manuel de votre appareil et un technicien qualifié avant toute réparation.