Que signifie C01 sur FLA48250 ?

BMS reports total battery pack voltage above the upper protection threshold. Fix: Restart the unit. if the error persists, contact the repair center.

Que signifie C02 sur FLA48250 ?

BMS reports total battery pack voltage below the lower protection threshold. Fix: Restart the unit. if the error persists, contact the repair center.

Que signifie C03 sur FLA48250 ?

Individual cell voltage has exceeded its upper protection threshold. Fix: Restart the unit. if the error persists, contact the repair center.

Que signifie C04 sur FLA48250 ?

Individual cell voltage has fallen below its lower protection threshold. Fix: Restart the unit. if the error persists, contact the repair center.

Que signifie C05 sur FLA48250 ?

Charging current exceeds the BMS protection limit. Fix: Restart the unit. if the error persists, contact the repair center.

Que signifie C06 sur FLA48250 ?

Discharge current exceeds the BMS protection limit. Fix: Restart the unit. if the error persists, contact the repair center.

Que signifie C07 sur FLA48250 ?

MOSFET (power switch) temperature is over the protection limit. Cause: 1. The inner temperature is over the limitation. 2. Check whether the ambient temperature is too high. Fix: Reduce ambient/inner temperature; allow the unit to cool. Verify ventilation and that ambient temperature is within the operating range.

Que signifie C09 sur FLA48250 ?

Battery cell temperature has exceeded its upper protection threshold. Fix: Restart the unit. if the error persists, contact the repair center.

Que signifie C10 sur FLA48250 ?

Battery cell temperature has fallen below its lower protection threshold. Fix: Restart the unit. if the error persists, contact the repair center.

Que signifie C11 sur FLA48250 ?

BMS detected an abnormal reading from the current sampling circuit. Fix: Restart the unit. if the error persists, contact the repair center.

Que signifie C12 sur FLA48250 ?

BMS detected abnormal output impedance on the DC output path. Fix: Restart the unit. if the error persists, contact the repair center.

Que signifie C14 sur FLA48250 ?

BMS detected loss of output from the battery pack (no power on the output side). Cause: Circuit breaker may be open, or the fuse may be blown. Fix: 1. Please check whether the circuit breaker is closed. 2. Please check whether the fuse is normal. 3. Restart the unit. if the error persists, contact the repair center.

FLA48250

Batterie14 codes

14 Critique

C01Battery overvoltage.Critique

Description

BMS reports total battery pack voltage above the upper protection threshold.

Correction recommandée

Restart the unit. if the error persists, contact the repair center.

Source:6peluqppy_66a93554057c8.pdf · page 12

C02Battery undervoltage.Critique

Description

BMS reports total battery pack voltage below the lower protection threshold.

Correction recommandée

Restart the unit. if the error persists, contact the repair center.

Source:6peluqppy_66a93554057c8.pdf · page 12

C03Cell overvoltage.Critique

Description

Individual cell voltage has exceeded its upper protection threshold.

Correction recommandée

Restart the unit. if the error persists, contact the repair center.

Source:6peluqppy_66a93554057c8.pdf · page 12

C04Cell undervoltage.Critique

Description

Individual cell voltage has fallen below its lower protection threshold.

Correction recommandée

Restart the unit. if the error persists, contact the repair center.

Source:6peluqppy_66a93554057c8.pdf · page 12

C05Charge overcurrent.Critique

Description

Charging current exceeds the BMS protection limit.

Correction recommandée

Restart the unit. if the error persists, contact the repair center.

Source:6peluqppy_66a93554057c8.pdf · page 12

C06Discharge overcurrent.Critique

Description

Discharge current exceeds the BMS protection limit.

Correction recommandée

Restart the unit. if the error persists, contact the repair center.

Source:6peluqppy_66a93554057c8.pdf · page 12

C07MOS overtemperature.Critique

Description

MOSFET (power switch) temperature is over the protection limit.

Cause

1. The inner temperature is over the limitation. 2. Check whether the ambient temperature is too high.

Correction recommandée

Reduce ambient/inner temperature; allow the unit to cool. Verify ventilation and that ambient temperature is within the operating range.

Source:6peluqppy_66a93554057c8.pdf · page 12

C08MOS undertemperature.Critique

Description

MOSFET (power switch) temperature is below the protection limit.

Cause

1. The internal temperature is lower than the limit range. 2. Check whether the ambient temperature is too low.

Correction recommandée

Raise ambient/inner temperature; verify ambient temperature is within the operating range.

Source:6peluqppy_66a93554057c8.pdf · page 12

C09Cell overtemperature.Critique

Description

Battery cell temperature has exceeded its upper protection threshold.

Correction recommandée

Restart the unit. if the error persists, contact the repair center.

Source:6peluqppy_66a93554057c8.pdf · page 13

C10Cell undertemperature.Critique

Description

Battery cell temperature has fallen below its lower protection threshold.

Correction recommandée

Restart the unit. if the error persists, contact the repair center.

Source:6peluqppy_66a93554057c8.pdf · page 13

C11Abnormal current sampling.Critique

Description

BMS detected an abnormal reading from the current sampling circuit.

Correction recommandée

Restart the unit. if the error persists, contact the repair center.

Source:6peluqppy_66a93554057c8.pdf · page 13

C12Abnormal output impedance.Critique

Description

BMS detected abnormal output impedance on the DC output path.

Correction recommandée

Restart the unit. if the error persists, contact the repair center.

Source:6peluqppy_66a93554057c8.pdf · page 13

C13Parallel failed.Critique

Description

Battery pack failed to establish or maintain parallel operation with other packs.

Cause

Single unit may be incorrectly set to parallel system; or wiring between parallel-connected battery packs is incorrect/incomplete.

Correction recommandée

1. Please check if a single unit is installed to the parallel system. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please finish parallel installation first, and then restart the unit. 3. if the problem remains, please contact your installer.

Source:6peluqppy_66a93554057c8.pdf · page 13

C14Output loss.Critique

Description

BMS detected loss of output from the battery pack (no power on the output side).

Cause

Circuit breaker may be open, or the fuse may be blown.

Correction recommandée

1. Please check whether the circuit breaker is closed. 2. Please check whether the fuse is normal. 3. Restart the unit. if the error persists, contact the repair center.

Source:6peluqppy_66a93554057c8.pdf · page 13

Codes courants sur cet appareil

C05

Charge overcurrent.

C06

Discharge overcurrent.

C01

Battery overvoltage.

C02

Battery undervoltage.

MOS undertemperature.

C09

Cell overtemperature.

C10

Cell undertemperature.

C11

Abnormal current sampling.

C12

Abnormal output impedance.

Compilé à partir des manuels utilisateur officiels FelicityESS. Consultez toujours le manuel de votre appareil et un technicien qualifié avant toute réparation.