Que signifie F01 sur IVEM 6048 ?

Fault: Bus voltage is too high. Cause: AC Surge or internal components failed. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F02 sur IVEM 6048 ?

Fault: Bus voltage is too low. Cause: Internal components failed (inferred from similar fault classes). Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F03 sur IVEM 6048 ?

Fault: Bus soft start fail. Cause: Internal components failed. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F04 sur IVEM 6048 ?

Fault: Inverter soft start fail. Cause: Internal components failed. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F05 sur IVEM 6048 ?

Fault: Over current or surge detected by Software. Cause: Software-detected overcurrent or surge condition. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F06 sur IVEM 6048 ?

Fault: Over current or surge detected by hardware. Cause: Hardware-detected overcurrent or surge condition. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F07 sur IVEM 6048 ?

Fault: Output voltage is too low. Cause: Connected load is too high or internal failure. Fix: Reduce the connected load. Restart the unit, if the error persists, contact the repair center.

Que signifie F08 sur IVEM 6048 ?

Fault: Output voltage is too high. Cause: Internal failure causing high output voltage. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F09 sur IVEM 6048 ?

Fault: Output short circuited. Cause: Wiring issue or abnormal load causing a short circuit. Fix: Check if wiring is connected well and remove abnormal load.

Que signifie F10 sur IVEM 6048 ?

Fault: Overload time out. Cause: Sustained overload condition. Fix: Reduce the connected load by switching off some equipment.

Que signifie F11 sur IVEM 6048 ?

Fault: Battery voltage is too high. Cause: Battery spec/quantity does not meet inverter requirements. Fix: Check if spec and quantity of batteries are meet requirements.

Que signifie F12 sur IVEM 6048 ?

Fault: Over current happen at DCDC circuit. Cause: Overcurrent in the DC/DC stage. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F13 sur IVEM 6048 ?

Fault: PV voltage is too high. Cause: Too many PV modules connected in series. Fix: Reduce the number of PV modules in series.

Que signifie F14 sur IVEM 6048 ?

Fault: Short circuited happen at PV port. Cause: Wiring issue causing short at PV port. Fix: Check if wiring is connected well.

Que signifie F16 sur IVEM 6048 ?

Fault: Over current happen at PV port. Cause: Overcurrent at the PV input. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F17 sur IVEM 6048 ?

Fault: Fan is locked. Cause: Fan wiring not connected well or fan failed. Fix: Check if wiring is connected well. Replace the fan.

Que signifie F18 sur IVEM 6048 ?

Fault: Over temperature happen at PV circuit. Cause: The temperature of internal PV converter component is over the limitation. Fix: Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.

Que signifie F19 sur IVEM 6048 ?

Fault: Over temperature happen at battery circuit. Cause: The temperature of internal battery converter component is over the limitation. Fix: Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.

Que signifie F20 sur IVEM 6048 ?

Fault: Over temperature happen at inverter circuit. Cause: The temperature of internal inverter component is over the limitation. Fix: Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.

Que signifie F21 sur IVEM 6048 ?

Fault: The inner temperature over. Cause: The inner temperature is over the limitation. Fix: Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.

Que signifie F22 sur IVEM 6048 ?

Fault: DCDC current sensor failed. Cause: DC/DC current sensor hardware failure. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F23 sur IVEM 6048 ?

Fault: No.2 DCDC current sensor failed. Cause: Second DC/DC current sensor hardware failure. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F24 sur IVEM 6048 ?

Fault: Inverter current sensor failed. Cause: Inverter current sensor hardware failure. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F25 sur IVEM 6048 ?

Fault: OP current sensor failed. Cause: Output current sensor hardware failure. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F26 sur IVEM 6048 ?

Fault: Sharing current sensor failed. Cause: Sharing current sensor hardware failure (parallel operation). Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F29 sur IVEM 6048 ?

Fault: DC/DC soft start fail. Cause: Internal failure during DC/DC soft start. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F31 sur IVEM 6048 ?

Fault: Over temperature happen at convert H circuit. Cause: The temperature of internal convert H component is over the limitation. Fix: Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.

Que signifie F32 sur IVEM 6048 ?

Fault: Over temperature happen at LLC TX. Cause: The temperature of internal DC/DC TX is over the limitation. Fix: Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.

Que signifie F33 sur IVEM 6048 ?

Fault: Over current happen at LLC circuit. Cause: Overcurrent in LLC resonant circuit. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F35 sur IVEM 6048 ?

Fault: Overvoltage occurs in BUS. Cause: AC surge or PV surge or internal components failed. Fix: Restart the unit, if the error persists, contact the repair center.

Que signifie F40 sur IVEM 6048 ?

Fault: CAN data loss. Cause: Communication cable connection issue between paralleled inverters. Fix: 1. Check if communication cables are connected well and restart the inverter. 2. if the problem remains, please contact your installer.

Que signifie F41 sur IVEM 6048 ?

Fault: Host data loss. Cause: Communication cable connection issue between paralleled inverters. Fix: 1. Check if communication cables are connected well and restart the inverter. 2. if the problem remains, please contact your installer.

Que signifie F42 sur IVEM 6048 ?

Fault: Synchronization data loss. Cause: Communication cable connection issue between paralleled inverters. Fix: 1. Check if communication cables are connected well and restart the inverter. 2. if the problem remains, please contact your installer.

Que signifie F45 sur IVEM 6048 ?

Fault: The output current of each inverter is different. Cause: Sharing cables not connected well between paralleled inverters. Fix: 1. Check if sharing cables are connected well and restart the inverter. 2. if the problem remains, please contact your installer.

Que signifie W01 sur IVEM 6048 ?

Warning: Fan is locked. Beep three times every second. Cause: Fan wiring not connected well or fan failure. Fix: Check if the Fan's wiring connected well. Replace the fan.

Que signifie W03 sur IVEM 6048 ?

Warning: Low battery. Beep once every second. Cause: The battery voltage is too low. Fix: The battery voltage is too low, it should be charging.

Que signifie W51 sur IVEM 6048 ?

Warning: BMS doesn't allow inverter to charge battery. Cause: BMS has prohibited charging. Fix: Inverter will stop charging battery automatically.

Que signifie W52 sur IVEM 6048 ?

Warning: BMS doesn't allow inverter to discharge battery. Cause: BMS has prohibited discharging. Fix: Inverter will stop discharging battery automatically.

Que signifie W53 sur IVEM 6048 ?

Warning: BMS require inverter to charge battery. Cause: BMS has requested charging. Fix: Inverter will charge battery automatically.

IVEM 6048

Onduleur49 codes

also coversIVEM6048

40 Défaut 9 Avertissement

F01Bus voltage is too high.Défaut

Description

Fault: Bus voltage is too high.

Cause

AC Surge or internal components failed.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

F02Bus voltage is too low.Défaut

Description

Fault: Bus voltage is too low.

Cause

Internal components failed (inferred from similar fault classes).

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

F03Bus soft start fail.Défaut

Description

Fault: Bus soft start fail.

Cause

Internal components failed.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

F04Inverter soft start fail.Défaut

Description

Fault: Inverter soft start fail.

Cause

Internal components failed.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

F05Over current or surge detected by Software.Défaut

Description

Fault: Over current or surge detected by Software.

Cause

Software-detected overcurrent or surge condition.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

F06Over current or surge detected by hardware.Défaut

Description

Fault: Over current or surge detected by hardware.

Cause

Hardware-detected overcurrent or surge condition.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

F07Output voltage is too low.Défaut

Description

Fault: Output voltage is too low.

Cause

Connected load is too high or internal failure.

Correction recommandée

Reduce the connected load. Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F08Output voltage is too high.Défaut

Description

Fault: Output voltage is too high.

Cause

Internal failure causing high output voltage.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F09Output short circuited.Défaut

Description

Fault: Output short circuited.

Cause

Wiring issue or abnormal load causing a short circuit.

Correction recommandée

Check if wiring is connected well and remove abnormal load.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F10Overload time out.Défaut

Description

Fault: Overload time out.

Cause

Sustained overload condition.

Correction recommandée

Reduce the connected load by switching off some equipment.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F11Battery voltage is too high.Défaut

Description

Fault: Battery voltage is too high.

Cause

Battery spec/quantity does not meet inverter requirements.

Correction recommandée

Check if spec and quantity of batteries are meet requirements.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F12Over current happen at DCDC circuit.Défaut

Description

Fault: Over current happen at DCDC circuit.

Cause

Overcurrent in the DC/DC stage.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F13PV voltage is too high.Défaut

Description

Fault: PV voltage is too high.

Cause

Too many PV modules connected in series.

Correction recommandée

Reduce the number of PV modules in series.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F14Short circuited happen at PV port.Défaut

Description

Fault: Short circuited happen at PV port.

Cause

Wiring issue causing short at PV port.

Correction recommandée

Check if wiring is connected well.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F15PV power is abnormal.Défaut

Description

Fault: PV power is abnormal.

Cause

PV power exceeds normal limits (too many PV modules).

Correction recommandée

Reduce the number of PV modules.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F16Over current happen at PV port.Défaut

Description

Fault: Over current happen at PV port.

Cause

Overcurrent at the PV input.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F17Fan is locked.Défaut

Description

Fault: Fan is locked.

Cause

Fan wiring not connected well or fan failed.

Correction recommandée

Check if wiring is connected well. Replace the fan.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F18Over temperature happen at PV circuit.Défaut

Description

Fault: Over temperature happen at PV circuit.

Cause

The temperature of internal PV converter component is over the limitation.

Correction recommandée

Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F19Over temperature happen at battery circuit.Défaut

Description

Fault: Over temperature happen at battery circuit.

Cause

The temperature of internal battery converter component is over the limitation.

Correction recommandée

Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F20Over temperature happen at inverter circuit.Défaut

Description

Fault: Over temperature happen at inverter circuit.

Cause

The temperature of internal inverter component is over the limitation.

Correction recommandée

Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F21The inner temperature over.Défaut

Description

Fault: The inner temperature over.

Cause

The inner temperature is over the limitation.

Correction recommandée

Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F22DCDC current sensor failed.Défaut

Description

Fault: DCDC current sensor failed.

Cause

DC/DC current sensor hardware failure.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F23No.2 DCDC current sensor failed.Défaut

Description

Fault: No.2 DCDC current sensor failed.

Cause

Second DC/DC current sensor hardware failure.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F24Inverter current sensor failed.Défaut

Description

Fault: Inverter current sensor failed.

Cause

Inverter current sensor hardware failure.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F25OP current sensor failed.Défaut

Description

Fault: OP current sensor failed.

Cause

Output current sensor hardware failure.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F26Sharing current sensor failed.Défaut

Description

Fault: Sharing current sensor failed.

Cause

Sharing current sensor hardware failure (parallel operation).

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 37

F27The AC input and output wires are inversely connected.Défaut

Description

Fault: The AC input and output wires are inversely connected.

Cause

AC input and output wires are reversed.

Correction recommandée

1. Please check AC input and output wires are connected correctly. 2. if this error happens during parallel installation, please check wires connection. if they are connected correctly, please funish parallel installation first, and then restart inverters. 3. if the problem remains, please contact your installer.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 38

F28Single unit is installed to parallel system.Défaut

Description

Fault: Single unit is installed to parallel system.

Cause

A single unit configuration was installed where parallel was expected.

Correction recommandée

1. Please check if single unit is installed to parallel system. 2. if this error happens during parallel installation, please check wires connectiotn. if they are connected correctly, please funish parallel installation first, and then restart inverters. 3. if the problem remains, please contact your installer.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 38

F29DC/DC soft start fail.Défaut

Description

Fault: DC/DC soft start fail.

Cause

Internal failure during DC/DC soft start.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 38

F31Over temperature happen at convert H circuit.Défaut

Description

Fault: Over temperature happen at convert H circuit.

Cause

The temperature of internal convert H component is over the limitation.

Correction recommandée

Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 38

F32Over temperature happen at LLC TX.Défaut

Description

Fault: Over temperature happen at LLC TX.

Cause

The temperature of internal DC/DC TX is over the limitation.

Correction recommandée

Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 38

F33Over current happen at LLC circuit.Défaut

Description

Fault: Over current happen at LLC circuit.

Cause

Overcurrent in LLC resonant circuit.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 38

F35Overvoltage occurs in BUS.Défaut

Description

Fault: Overvoltage occurs in BUS.

Cause

AC surge or PV surge or internal components failed.

Correction recommandée

Restart the unit, if the error persists, contact the repair center.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 38

F40CAN data loss.Défaut

Description

Fault: CAN data loss.

Cause

Communication cable connection issue between paralleled inverters.

Correction recommandée

1. Check if communication cables are connected well and restart the inverter. 2. if the problem remains, please contact your installer.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 38

F41Host data loss.Défaut

Description

Fault: Host data loss.

Cause

Communication cable connection issue between paralleled inverters.

Correction recommandée

1. Check if communication cables are connected well and restart the inverter. 2. if the problem remains, please contact your installer.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 38

F42Synchronization data loss.Défaut

Description

Fault: Synchronization data loss.

Cause

Communication cable connection issue between paralleled inverters.

Correction recommandée

1. Check if communication cables are connected well and restart the inverter. 2. if the problem remains, please contact your installer.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 38

F43Current feedback into the inverter is detected.Défaut

Description

Fault: Current feedback into the inverter is detected.

Cause

Reverse-connected L/N cables or improper sharing-cable wiring in parallel/three-phase systems.

Correction recommandée

1. Restart the inverter. 2. Check if L/N cables are not connected reversely in all inverters. 3. For parallel system in single phase, make sure the sharing cables are connected in all inverters. For supporting three-phase system, make sure the sharing cables are connected in the inverters in the same phase, and disconnected in the inverters in different phases. 4. if the problem remains, please contact your installer.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 38

F44The firmware version of each inverter is not the same.Défaut

Description

Fault: The firmware version of each inverter is not the same.

Cause

CPU/firmware versions differ between paralleled inverters.

Correction recommandée

1. Update all inverter firmware to the same version. 2. Check the version of each inverter via LCD setting and make sure the CPU versions are same. if not, please contact your installer to provide the firmware to update. 3. After updating, if the problem still remains, please contact your installer.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 38

F45The output current of each inverter is different.Défaut

Description

Fault: The output current of each inverter is different.

Cause

Sharing cables not connected well between paralleled inverters.

Correction recommandée

1. Check if sharing cables are connected well and restart the inverter. 2. if the problem remains, please contact your installer.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 39

F46AC output mode setting is different.Défaut

Description

Fault: AC output mode setting is different.

Cause

Inconsistent AC output mode (program 28) settings across paralleled inverters.

Correction recommandée

1. Switch off the inverter and check LCD setting program 28. 2. For parallel system in single phase, make sure no 3P1, 3P2 or 3P3 is set on program 28. For supporting three-phase system, make sure no "PAL" is set on program 28. 3. if the problem remains, please contact your installer.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 39

W01Fan is locked.Avertissement

Description

Warning: Fan is locked. Beep three times every second.

Cause

Fan wiring not connected well or fan failure.

Correction recommandée

Check if the Fan's wiring connected well. Replace the fan.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

W02Overload.Avertissement

Description

Warning: Overload. Beep twice every second.

Cause

Connected load exceeds the inverter capacity.

Correction recommandée

Reduce the loads.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

W03Low battery.Avertissement

Description

Warning: Low battery. Beep once every second.

Cause

The battery voltage is too low.

Correction recommandée

The battery voltage is too low, it should be charging.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

W50BMS firmware version is not matched.Avertissement

Description

Warning: BMS firmware version is not matched.

Cause

BMS firmware version mismatch.

Correction recommandée

Upgrade the firmware of BMS.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

W51BMS doesn't allow inverter to charge battery.Avertissement

Description

Warning: BMS doesn't allow inverter to charge battery.

Cause

BMS has prohibited charging.

Correction recommandée

Inverter will stop charging battery automatically.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

W52BMS doesn't allow inverter to discharge battery.Avertissement

Description

Warning: BMS doesn't allow inverter to discharge battery.

Cause

BMS has prohibited discharging.

Correction recommandée

Inverter will stop discharging battery automatically.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

W53BMS require inverter to charge battery.Avertissement

Description

Warning: BMS require inverter to charge battery.

Cause

BMS has requested charging.

Correction recommandée

Inverter will charge battery automatically.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

W54~65BMS detect something wrongs happened.Avertissement

Description

Warning: BMS detect something wrongs happened (range covering codes 54 through 65).

Cause

BMS has detected an internal abnormality.

Correction recommandée

If the code is keeping for long time, please contact with your installer.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

W80BMS communication fault.Avertissement

Description

Warning: BMS communication fault.

Cause

Communication line between BMS and inverter is not connected well.

Correction recommandée

Check if the communication line is connected well.

Source:felicitysolar IVEM 6048 Solar Inverter User Guide.pdf · page 36

Codes courants sur cet appareil

F01

Bus voltage is too high.

F02

Bus voltage is too low.

F04

Inverter soft start fail.

F07

Output voltage is too low.

F11

Battery voltage is too high.

F15

PV power is abnormal.

F17

Fan is locked.

F19

Over temperature happen at battery circuit.

F21

The inner temperature over.

F22

DCDC current sensor failed.

F23

No.2 DCDC current sensor failed.

F24

Inverter current sensor failed.

Compilé à partir des manuels utilisateur officiels FelicityESS. Consultez toujours le manuel de votre appareil et un technicien qualifié avant toute réparation.