Is the FAULT: LED1=ON, LED2=OFF, LED3=ON, LED4=OFF (Green OFF, Red ON) fix the same on every device?

The cause is consistent — it's the same protection logic. The exact fix wording can differ per device because each official manual addresses model-specific context (input ranges, parallel-config notes, firmware revisions). Use the per-device section that matches your unit.

Where does this information come from?

Every entry is sourced directly from the official Felicity user manual for the affected device. The "Source" line at the bottom of each device's section shows the manual filename and page number.

Fault

FAULT: LED1=ON, LED2=OFF, LED3=ON, LED4=OFF (Green OFF, Red ON)

Q: Can I clear the FAULT: LED1=ON, LED2=OFF, LED3=ON, LED4=OFF (Green OFF, Red ON) code myself?

It depends on the severity. Warning-level codes can usually be cleared by following the recommended fix. Fault and critical codes often require checking the source condition first; if the code returns immediately after restart, escalate to authorized service.

Q: What does FAULT: LED1=ON, LED2=OFF, LED3=ON, LED4=OFF (Green OFF, Red ON) mean on LPBF24200-M?

Charging over-current protection has tripped. Cause: Charge current exceeded the recommended limit (e.g. >80 A on LPBF24200-M / LPBF48200-M/P) or the 15 s 120 A maximum for too long. Recommended fix: Reduce the charge current at the charger / inverter to within the recommended setting in section 2.4. For systems above 6 kVA at least 2 packs in parallel are required.

Charging Current High.

2 Devices that report this code

What does the FAULT: LED1=ON, LED2=OFF, LED3=ON, LED4=OFF (Green OFF, Red ON) error code mean?

FAULT: LED1=ON, LED2=OFF, LED3=ON, LED4=OFF (Green OFF, Red ON) on a Felicity unit indicates: Charging Current High.. It is a fault-severity event that can appear on 2 different devices in the Felicity catalog. The same code may have slightly different recommended fixes depending on the device — the per-device sections below show the exact wording from each device's official manual.

This is a fault-severity code

Fault codes stop normal operation but the unit may attempt to recover. Common causes are out-of-range conditions (voltage, current, temperature) that require checking inputs and outputs before restart.

What triggers this code

FAULT: LED1=ON, LED2=OFF, LED3=ON, LED4=OFF (Green OFF, Red ON) is triggered when the unit's protection or monitoring logic detects the specific condition described above. The exact trigger depends on the device — see the per-device sections for the official manual entry for each.

LPBF24200-MBattery↗ view on device

FAULT: LED1=ON, LED2=OFF, LED3=ON, LED4=OFF (Green OFF, Red ON)Charging Current High.Fault

Description

Charging over-current protection has tripped.

Cause

Charge current exceeded the recommended limit (e.g. >80 A on LPBF24200-M / LPBF48200-M/P) or the 15 s 120 A maximum for too long.

Recommended fix

Reduce the charge current at the charger / inverter to within the recommended setting in section 2.4. For systems above 6 kVA at least 2 packs in parallel are required.

Source:Felicitysolar LPBF24200-M LiFePO4 Battery System for Households User Guide.pdf · page 9

LPBF48250Battery↗ view on device

FAULT: LED1=ON, LED2=OFF, LED3=ON, LED4=OFF (Green OFF, Red ON)Charging Current High.Fault

Description

Charge over-current protection has tripped. Listed in the FAULT row of the LED table on page 7 as 'CHARGING CURRENT HIGH'.

Cause

Charge current exceeded the recommended limit. Per section 2.3 the recommended charge & discharge current is <=120 A and the absolute MAX is 200 A for 15 s; per section 2.4 Max. Charging Current is 120 A * N (N = number of packs in parallel). The protection trips when these limits are exceeded.

Recommended fix

Reduce the charge current at the charger / inverter to within 120 A per pack (section 2.4). For inverters larger than 6 kVA, install at least 2 sets of LPBF48V in parallel connection (section 1.3 item 9 and section 3.2).

Source:Battery Manual LPBF48250 (EN).pdf · page 7

Frequently asked about FAULT: LED1=ON, LED2=OFF, LED3=ON, LED4=OFF (Green OFF, Red ON)

What is the FAULT: LED1=ON, LED2=OFF, LED3=ON, LED4=OFF (Green OFF, Red ON) error on Felicity?: FAULT: LED1=ON, LED2=OFF, LED3=ON, LED4=OFF (Green OFF, Red ON) on a Felicity unit means: Charging Current High.. It can appear on 2 different devices in the Felicity catalog. The cause and recommended fix are listed for each device on this page.
Can I clear the FAULT: LED1=ON, LED2=OFF, LED3=ON, LED4=OFF (Green OFF, Red ON) code myself?: It depends on the severity. Warning-level codes can usually be cleared by following the recommended fix. Fault and critical codes often require checking the source condition first; if the code returns immediately after restart, escalate to authorized service.
Is the FAULT: LED1=ON, LED2=OFF, LED3=ON, LED4=OFF (Green OFF, Red ON) fix the same on every device?: The cause is consistent — it's the same protection logic. The exact fix wording can differ per device because each official manual addresses model-specific context (input ranges, parallel-config notes, firmware revisions). Use the per-device section that matches your unit.
Where does this information come from?: Every entry is sourced directly from the official Felicity user manual for the affected device. The "Source" line at the bottom of each device's section shows the manual filename and page number.

Compiled from official Felicity user manuals. Always consult your device manual and a qualified technician before performing repairs.